Operating instructions Kullanım kılavuzu
Transkript
Operating instructions Kullanım kılavuzu
Operating instructions Kullanım kılavuzu Bypass level indicator model BNA GB Bypass Seviye Göstergesi Model BNA TR Bypass level indicator, model BNA with option level sensor and magnetic switch A division of the WIKA Group TR Operating instructions bypass level indicator Model BNA Bypass seviye göstergesi kullanım kılavuzu Model BNA 2 Page 3-16 Sayfa17-30 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D GB Contents Contents GB 1. Safety instructions 4 3. Installation and commissioning 7 2. 4. 5. Description of functions and design Maintenance Error detection 6 15 16 WARNING! Instructions on correct installation and proper operation. Non-observance of these instructions can lead to malfunction or damage. DANGER! Instructions which must be complied with to avoid injury or property damage. based on 11/2012 GB/D Information Facts and information concerning proper operation. KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 3 1. Safety instructions 1. Safety instructions Please read these instructions carefully before installing and commissioning the model BNA bypass level indicator. These instructions are directed to trained personnel implementing the assembly, installation and set-up of the system. The bypass level indicator serves for continuously measuring the level of liquids in vessels. Use it for no purpose other than this. No liability will be assumed by the manufacturer for damage resulting from use other than specified! The bypass level indicator has been designed, manufactured and tested in accordance with the state of art and the accepted safety regulations. Notwithstanding this, certain risks might be involved. GB The following safety instructions should, therefore, be observed: Do not modify, supplement or change the bypass level indicator unless with manufacturer’s express approval. Unauthorised changes or non-permitted use will result in immediate loss of warranty or liability claims. The installation, operation and maintenance must be performed by expert and authorised personnel only. The required expertise must be obtained by regular training. Prior to starting operation please check all devices for their proper connection, operability and power supply. This shall also apply to assemblies coupled thereto. 4 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D It is imperative for operators, installers and servicers to comply with all applicable safety regulations. This provision shall extend to all local safety and accident preventing regulations not expressly referred to herein. 1. Safety instructions The general operating instructions of all devices as used must be abided by. GB Measures must be taken preventing personal injuries and damage to property from occurring in case of a defective condition of the bypass level indicators. The bypass level indicator must not be operated in the direct vicinity of ferromagnetic environments (min. distance 50 mm) or strong electromagnetic fields (min. distance 1 m). The bypass level indicator must not be exposed to heavy mechanical strain. The maximum power and voltage values for the intrinsically safe operation as specified in the assembling and operating instructions should be adhered to. based on 11/2012 GB/D The safe operation of the system with a view to pressure and temperature of the materials as employed shall be the operator’s responsibility. The medium to be monitored must not be heavily soiled or contain coarse particles. It must not tend to stick or crystallise, as otherwise the perfect function cannot be guaranteed. The bypass level indicators may only be used in accordance with the maximum values for pressure and temperature as stated on the product label. Exceeding these parameters can lead to malfunctions or to the destruction of the bypass level indicator and may cause personal injury or damage to property. All materials of the bypass tube and the float must be resistant to the medium to be monitored. KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 5 1. Safety instructions / 2. Functional description ... The maximum values specified on the product label must be observed to guarantee trouble-free operation. At temperatures over 60 °C, a warning sign has to be attached to flanges, tubes, case etc., warning explicitly of the danger of burning and suitable protective measures must also be taken. GB The float has been designed for the medium density specified on the product label. When the float is used in liquids with another specific weight, deviations can occur during measurement. DANGER! Work in containers involves the danger of intoxication and suffocation. No work is allowed to be carried out unless by taking suitable personal protective measures (e.g. respiratory protection apparatus, protective outfit etc.). Danger of explosion Inside the container, there is danger of an explosive atmosphere. Corresponding measures for preventing sparking should be taken. No work is allowed in this area unless by technically skilled staff in accordance with applicable safety regulations. KSR KUEBLER bypass level indicators work according to the principle of communicating vessels. The bypass vessel contains a float with a built-in permanent magnet. This rises and falls with the level of the medium. Optical and electrical level indicators or limit switches are mounted to the outside of the bypass tube and actuated by the magnetic field. Evaluation of the filling level by guided radar is also possible. The 6 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D 2. Functional description and design 2. Functional description and ... / 3. Installation and ... fitting of these options is carried out according to specific customer wishes in the factory. The principle structure is shown in figure 1. Customer-specific versions are executed to order. Transport and storage Transport and storage for bypass level indicators are only allowed in designed packaging. Removal of transport packaging and transportation safety devices Remove the bypass level indicator carefully from the transport packaging. Please observe the instructions given on the shipment packaging and remove all transportation safety devices before taking out the bypass level indicator. Never use force to remove the bypass level indicator from the packaging! Before fitting, loosen the float attached on the outside of the bypass level indicator from the bypass vessel. Make sure that all parts of the packaging have been removed and the float can move freely in the bypass reference vessel. 3. Installation and commissioning based on 11/2012 GB/D Remove the protective caps on the process connections before fitting. Check the connection dimensions (centre to centre distance) and the alignment of the process connections on the vessel. There must not be any mechanical damage on the sealing faces of the vessel or the bypass level indicator. The magnetic roller display and any installed magnetic switches must be aligned. To do this, slowly move the enclosed float from bottom to top on the magnetic roller display and then back down again. Magnetic switches must be aligned on the basis of the same principle. In the case of bypass level indicators with insulation and magnetic roller displays KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 7 GB 3. Installation and commissioning with Plexiglass attachments, the float must be moved up and down inside the tube. For magnetic roller displays with flushing connections, GB these connections must have an airtight seal. Please refer in this case to the mounting and operating instructions for KSR KUEBLER magnetic roller displays with flushing connections as well. The bypass level indicator is mounted in a vertical position on the vessel to be monitored using the process connections (1) provided. Seals (2), screws (3), washers (4) and nuts (5) suitable for the process connection must be used. Choose a seal with a suitable corrosion resistance. If necessary, shut-off valves must be mounted between the vessel and the bypass. Please heed the usual torque values of screws used in pipefitting work. The bypass level indicator must be installed without tension. Suitable seals must be used. Care must be taken that the seal material is resistant to the medium and its vapours as well as to the temperature and pressure loads to be expected. Installing the float ■■ Clean the float of anything stuck on it in the area of the float magnet system ■■ Remove the base flange (7) and insert the float (6) into the tube from the bottom (the marking "top" or a legible model code marks the top side of the float) ■■ Place the seal (9) onto the base flange. Replace the base flange and fix it in place using the screws (8) ■■ Close draining and bleeding fittings on the bypass level indicator 8 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D Commissioning If the bypass level indicator is fitted with shut-off valves between process connections and tank, proceed as follows. 3. Installation and commissioning ■■ Slowly open the shut-off valve at the upper process connection Fig. 1: Bypass level indicator, model BNA GB ■■ Slowly open the shut-off valve at the lower process connection. As liquid flows into the bypass vessel, the float floats to the top. The magnetic system turns the magnetic rollers of the optical indicator from „light“ to „dark“. The current filling level is shown after liquid equalisation between the vessel and the bypass level indicator ■■ Always heed the based on 11/2012 GB/D mounting and operating instructions of attachment devices before putting them into operation T = upper projection M = centre to centre distance U = lower projection KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 9 3. Installation and commissioning The bypass tube can also be delivered in a heated doublewalled version. In this case, the bypass tube is surrounded by a second tube. Heated liquid or steam (heat carrier) can flow through this double-sheathed space via two connections. The materials for higher temperatures must be designed according to AD information sheets in non-corroding qualities. The heating sheath of the bypass level indicators may only be used according to the specified maximum values for pressure and temperature. Attachment of the evaluation devices to the bypass level indicator When attaching the evaluation devices (e.g.: KSR KUEBLER sensors MG …, KSR KUEBLER magnetic switches) to the BNA …, the respective maximum values of the field instrument must be heeded. The applicable laws or directives for the use or the planned purpose of application must also be observed. Attachment example (sensor MG… to the bypass tube) This description is only intended as an orientation aid for the local installation situation. Please refer to the mounting and operating instructions of the attachment devices as well. 10 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D GB Installation and commissioning of the bypass level indicator in a heated double-walled version 3. Installation and commissioning Fig. 2: Sensor to the bypass tube 1 Sensor MG ... 2 Tightening strap 3 Magnetic roller display 4 Cheese-head screw or comparable 5 Mounting clamp 6 Mounting lug GB Use the tightening strap or mounting clamp (pos. 5) to attach the sensor MG … to the bypass tube. based on 11/2012 GB/D The distance between the position sensor (magnetic system in the float) and the sensor tube should not exceed 8 mm depending on the magnetic system. The bypass tube must never be scored or drilled into or welded directly. KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 11 3. Installation and commissioning Attachment example (magnetic switch to magnetic roller display) The magnetic switch is attached to the magnetic roller level display (4) of the bypass level indicator (6) by means of sliding blocks (fig. 3). GB ■■ Loosen the mounting screws (1) on the magnetic switch by about one turn using an Allen key size 3 mm ■■ Push the sliding block(s) (2) into the guide groove (3) of the magnetic roller display (4) from the top or the bottom. (Please note the position of the cable connection or the plug as shown in the illustration) ■■ Push the magnetic switch to the height of the required switching point and fix in place by tightening the screws (the switch point is marked on the product label). 12 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D The magnetic switch MA has been designed for attachment on the right-hand side of the magnetic roller display (4). If it is mounted on the left-hand side, the switching function is reversed. The switch has to be mounted the other way round (product label is upside down). 3. Installation and commissioning Fig. 3: Mounting the magnetic switch (model M, ME, MST, MT) GB Switch point based on 11/2012 GB/D Mounting the magnetic switch (model MA) KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 13 3. Installation and commissioning Attachment example (magnetic switch to support bar) These magnetic switches are fixed to a separately attached support bar (fig. 4). GB ■■ Remove the support bar (1) by loosening the mounting screws (2) and removing the retaining plates (3) from the bypass stand seat ■■ Push the magnetic switch (4) onto the support bar (1) ■■ Attach the support bar (1) to the bypass tube (5) again using the retaining plates (3) and mounting screws (2) ■■ Push the magnetic switch to the height of the required switch point and fix in place by tightening the screws (6) (the switch point is marked on the product label) Please make sure during mounting that the cable entry and/ or the plug are pointing downwards. To guarantee a safe switching function, the magnetic switch housing must rest against the bypass tube. 14 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D Fig. 4: Mounting the magnetic switch (model MS, MV, MVT, MEx) 4. Maintenance 4. Maintenance When used properly, bypass level indicators work maintenance-free. They must be subjected to visual inspection within the context of regular servicing, however, and included in the tank pressure test. (The test pressure must not exceed the value specified on the product label!) If the liquid to be measured contains dirt particles that could be deposited in the bypass level indicator, the operator should clean the bypass chamber at regular intervals. DANGER! Work on containers involves the danger of intoxication and suffocation. No work is allowed to be carried out unless by taking suitable personal protective measures (e.g. respiratory protection apparatus, protective outfit etc.). The bypass vessel can be under pressure. There might be a hot, poisonous, caustic or explosive medium inside the bypass vessel. Potential injury hazard due to splashing liquid, burns to hands, arms, feet and face are possible, as well as chemical burns, poisoning or explosions. Vessel pressure has to be released before opening. based on 11/2012 GB/D Perfect functioning of the bypass level indicator can only be guaranteed when original accessories and spare parts are used. KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 15 GB 5. Trouble shooting 5. Trouble shooting GB The following table contains the most frequent causes of faults and the necessary countermeasures. Fault Cause Measure Bypass level indicator cannot be fitted at the planned place on the vessel Thread size or flange size of the bypass level indicator do not correlate Modification of the vessel Thread on the fastening sleeve on the vessel is faulty Mounting thread on the bypass level indicator is faulty Centre to centre distance of the vessel does not correlate with the bypass level indicator Rework the thread or replace the fastening sleeve Return to the factory Process connections are not attached parallel to one another Modification of the vessel Return to the factory Modification of the vessel Return to the factory 16 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D Please contact us if you have any difficulties. We will be happy to help any way we can. İçindekiler İçindekiler 1. Güvenlik bilgileri 18 3. Kurulum ve çalıştırma 21 2. 4. 5. Fonksiyon açıklaması ve yapısı Bakım Hata tespiti 20 29 30 UYARI! Kurallara uygun montaj ve usulüne uygun kullanım için uyarılar. Uyulmaması durumunda hatalı işlevler veya arızalar meydana gelebilir. TEHLİKE! Uyulmaması durumunda şahsi ve maddi hasarlara neden olabilecek uyarılar. based on 11/2012 GB/D Bilgi Kurallara uygun kullanım için veriler ve bilgiler. KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 17 TR 1. Güvenlik bilgileri 1. Güvenlik bilgileri Bypass seviye göstergesi Model BNA‘yı kurmadan ve çalıştırmadan önce bu kılavuzu okuyun. Bu kılavuz montajı, kurulumu ve ayarı gerçekleştirecek yetkili personel içindir. Bypass seviye göstergesi, kaplardaki sıvıların sürekli doluluk seviyesi ölçümü görevini görür. Onu sadece bu amaçla kullanın. Usulüne uygun olmayan kullanım sonucunda oluşan hasarlardan üretici sorumlu değildir! TR Bypass seviye göstergesi teknolojinin düzeyine ve kabul edilmiş emniyet teknolojisine dair kurallara uygun olarak geliştirilmiş, üretilmiş ve kontrol edilmiştir. Yine de alet tehlike arz edebilir. Bu nedenle şu güvenlik talimatlarına dikkat edin: Üreticiye önceden danışmadan Bypass seviye göstergesinde değişiklikler yapmayın. Yetkisiz müdahale ve izinsiz kullanım, garanti ve tazminat hakkını ortadan kaldırır. Kurulum, kullanım ve çalıştırma sadece yetkili bir uzman personel tarafından gerçekleştirilmelidir. Uzmanlıklar düzenli eğitim ile elde edilmiş olmalıdır. Çalıştırılmadan önce tüm cihazların bağlantılarının ve fonksiyonlarının doğruluğu kontrol edilmelidir. Ardından bağlanan cihazların da olmak üzere elektrik beslemesini kontrol edin. 18 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D Kullanan, ayarlayan ve çalıştıran kişiler tüm geçerli güvenlik talimatlarına dikkat etmelidir. Bunların içerisine bu kullanım kılavuzunda belirtilmemiş olan yerel güvenlik ve kaza önleme talimatları da dahildir. 1. Güvenlik bilgileri Kullanılan cihazların genel kullanım kılavuzlarına dikkat edilmelidir. Bypass seviye göstergesinin bozulması durumunda kişiler ve nesneler için meydana gelebilecek tehlikelerin engellenmesini sağlayacak önlem- TR ler alınmalıdır. Bypass seviye göstergesini ferromanyetik çevre yakınında (min. mesafe 50 mm) veya güçlü elektromanyetik alanların yakınında (min. mesafe 1 m) çalıştırmayın. Bypass seviye göstergeleri ağır mekanik yüklere maruz bırakılmamalıdır. Montaj ve kullanım kılavuzunda belirtilen maksimum akım ve gerilim değerlerine kendi güvenliğiniz için uyun. Tesisin güvenli kullanımı, basıncın ve kullanılan malzemelerin sıcaklığının kontrolü kullanıcıya aittir. Denetlenecek olan madde kirli ve iri parçalara sahip olmamalıdır. Sorunsuz çalışma sağlayabilmek için kristalleşme ve yapışma gibi özellikler göstermemelidir. based on 11/2012 GB/D Bypass seviye göstergeleri sadece ilgili model levhasında basınç ve sıcaklık için belirtilen maksimum değerlerle kullanıma alınmalıdır. Bu parametrelerin aşılması hatalı işlemlere, Bypass seviye göstergesinin zarar görmesine, şahsi ve maddi zararlara neden olabilir. Bypass borularının ve şamandıranın hammaddesi, denetlenen maddeye karşı dayanıklı olmalıdır. KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 19 1. Güvenlik bilgileri / 2. Fonksiyon açıklaması .. ... Sorunsuz bir işletimin sağlanması için model levhasında belirtilen maksimum değerlere dikkat edilmelidir. 60 °C‘nin üzerindeki sıcaklıklarda flanşlar, borular, gövde vs. üzerine yanma tehlikesini açıkça belirten bir uyarı bilgisi yerleştirilmelidir ve gerekli koruma önlemleri yerine getirilmelidir. TR Şamandıra, model levhasında belirtilen madde yoğunluğuna göre tasarlanmıştır. Farklı ağırlıklara sahip sıvılarla kullanılması durumunda ölçümde sapmalar meydana gelebilir. TEHLİKE! Kapların içerisinde yapılan çalışmalar sırasında zehirlenme veya boğulma tehlikesi meydana gelebilir. Çalışmalar sadece uygun şahsi koruma önlemleri alınarak (örn. nefes havasını koruma cihazı, koruyucu kıyafet, vs.) gerçekleştirilebilir. 2. Fonksiyon açıklaması ve yapısı KSR KUEBLER Bypass seviye göstergesi bileşik kaplar prensibine bağlı olarak çalışır. Kap içerisinde dahili kalıcı mıknatısa sahip bir şamandıra bulunur. 20 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D Dikkat Patlama tehlikesi Kazan içerisinde patlama tehlikesi taşıyan bir atmosfer mevcut olabilir. Kıvılcım oluşmasını engellemek için ilgili önemler alınmalıdır. Bu bölgelerdeki çalışmalar sadece yetkili personel tarafından ilgili güvenlik talimatlarına uygun olarak gerçekleştirilebilir. 2. Fonksiyon açıklaması ve ... / 3. Kurulum ve ... Bu, yüksekliğini kullanılan maddenin seviyesine göre değiştirir. Manyetik alan sayesinde Bypass borusuna monte edilmiş olan optik ve elektrikli doluluk seviyesi göstergeleri veya sınır değer şalteri tetiklenir. Doluluk seviyesinin değerlenmesi güdümlü radarla da mümkündür. Bu seçeneklerin yapısı ve montajı müşteriye bağlı olarak fabrikada gerçekleştirilir. Temel yapı resim 1'de görülebilir. Müşteriye bağlı modeller siparişe göre uygulanır. Nakliye ve depolama Bypass seviye göstergesinin taşınması ve depolanması için bu amaçla öngörülmüş paket kullanılmalıdır. Nakliye paketinin ve nakliye güvenliklerinin çıkartılması Bypass seviye göstergesini dikkatli bir şekilde nakliye paketinden çıkartın. Lütfen teslimat paketinin üzerinde bulunan uya rılara dikkat edin ve çıkartmadan önce tüm nakliye güvenliklerini sökün. Bypass seviye göstergesini asla zor kullanarak paketten çıkartmayın! Montajdan önce Bypass seviye göstergesine takılmış olan şamandırayı Bypass kazanından çözün. Tüm paketleme parçalarının çıkartılmış olduğundan ve şamandıranın Bypass temin kazanının içerisinde serbestçe hareket edebiliyor olduğundan emin olun. 3. Kurulum ve çalıştırma based on 11/2012 GB/D Montajdan önce işlem bağlantılarındaki koruyucu kapaklar çıkartılmalıdır. Bağlantı ölçülerini (merkez mesafesi) ve kaptaki işlem bağlantılarının sırasını kontrol edin. Kabın veya Bypass seviye göstergesinin sızdırmaz yüzeylerinde mekanik hasar bulunmamalıdır. Manyetik rulo göstergesi ve eğer mevcutsa manyetik şalter ayarlanmalıdır. Bunun için birlikte gelen şamandıra, manyetik rulo göstergesine yavaşça aşağıdan yukarıya, daha sonra tekrar aşağıya doğru hareket ettirilir. Monte edilmiş manyetik şalter de aynı prensiple ayarlanmalıdır. İzolasyonlu Bypass seviye göstergesinde veya pleksiglas tertibatlı manyetik rulo göstergelerinde şamandıra borunun içerisinde yukarı ve KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 21 TR 3. Kurulum ve çalıştırma aşağı hareket ettirilmelidir. TR Bypass seviye göstergesi öngörülmüş işlem bağlantılarıyla (1), dikey bir pozisyonda, denetlenecek olan kaba monte edilir. Montaj için işlem bağlantısına uygun contalar (2), vidalar (3), levhalı diskler (4) ve somunlar (5) kullanılmalıdır. Conta seçiminde ilgili korozyon dayanıklılığına dikkat edilmelidir. Gerekirse kap ve Bypass arasında izolasyon armatürleri monte edilmelidir. Lütfen boru hattı yapısının vidaları için gereken torka dikkat edin. Bypass seviye göstergesi gerilimsiz olarak monte edilmelidir. Uygun contalar kullanılmalıdır. Contalama malzemesinin kullanılan maddeye, buharlarına, oluşması beklenen sıcaklıklara ve basınçlara karşı dayanıklı olmasına dikkat edilmelidir. Şamandıranın montajı ■■ Şamandırayı, şamandıra manyetik sisteminin bölgesindeki olası yapışkan parçalardan temizleyin ■■ Taban flanşını (7) şamandırayı (6) alttan boruya sokun Servise koyma Bypass seviye göstergesi işlem bağlantıları ve kap arasında izolasyon valfleri ile donatılmışsa şu şekilde hareket edin. ■■ Bypass seviye göstergesindeki boşaltma ve havalandırma 22 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D (Şamandıranın „top“ veya okunaklı yazı kodu ile işaretlenmiş üst kısmı) ■■ Contayı (9) taban flanşına yerleştirin. Taban flanşını yeniden yerleştirin ve vidalarla (8) sabitleyin 3. Kurulum ve çalıştırma tertibatlarını kapatın ■■ Üst işlem bağlantısındaki izolasyon valfini yavaşça açın Şekil 1: Bypass seviye göstergesi Model BNA TR ■■ Alt işlem bağlantısındaki izolasyon valfini yavaşça açın. Bypass kabına sıvı akmaya başlayınca şamandıra yukarı doğru çıkar. Manyetik sistem, optik göstergenin manyetik rulolarını „açık“ taraftan „koyu“ tarafa doğru döndürür. Kap ve Bypass seviye göstergesi arasındaki sıvı dengelemesi sağlandıktan sonra güncel doluluk seviyesi gösterilir ■■ Yapı cihazlarının based on 11/2012 GB/D çalıştırılması için kesinlikle montaj ve kullanım kılavuzuna dikkat edin T = üst fazla mesafe M = Merkez mesafesi U = alt fazla mesafe KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 23 3. Kurulum ve çalıştırma Isıtmalı, çift duvarlı bir modelde Bypass seviye göstergesinin kurulumu ve çalıştırılması Bypass borusu ısıtmalı ve çift duvarlı modelde de kullanılabilir. Burada Bypass borusu ikinci bir boru ile kaplanır. Bu şekilde oluşturulan çift muhafaza alanına, iki bağlantı üzerinden ısıtılmış sıvı veya ısıtılmış buhar (ısı taşıyıcı) akıtılabilir. Daha yüksek sıcaklıklar için hammaddelerin tasarlanması AD pusulasına göre göre paslanmayan kalitelere göre yapılır. TR Bypass seviye göstergesinin ısıtma muhafazası sadece ilgili basınç ve sıcaklık için belirtilen maksimum değerlerle kullanıma alınmalıdır. Değerlendirme aygıtlarının Bypass seviye göstergesine monte edilmesi Değerlendirme aygıtlarının BNA ... üzerine montajı sırasında (örn.: KSR KUEBLER Ölçü değeri verici MG ..., KSR KUEBLER Manyetik şalter) alan cihazının ilgili maksimum değerlerine dikkat edilmelidir. Kullanım veya planlanan amaç için uygun olan yasa ve yönetmeliklere uyulmalıdır. Montaj örneği (Ölçü değeri verici MG ... Bypass borusuna) 24 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D Burada yapılan açıklama, sadece yerel montaj olasılıkları için oryantasyon yardımı olarak görülmelidir. Lütfen modüler cihazların montaj ve kullanım kılavuzuna da dikkat edin. 3. Kurulum ve çalıştırma Şekil 2: Bypass borusundaki ölçü değeri verici 1 Ölçü değeri verici MG ... 2 Germe bandı 3 Manyetik rulo göstergesi 4 Silindir başlı vida veya karşılaştırılabilir 5 sabitleme kelepçesi 6 Bağlantı ayağı TR Ölçüm değeri verici MG ... germe bandı veya sabitleme kelepçeleri ile (poz. 5) Bypass borusuna bağlanır. based on 11/2012 GB/D Pozisyon belirleyici (şamandıradaki manyetik sistem) ve ölçüm değeri verici boru arasındaki mesafe, manyetik sisteme bağlı olarak 8 mm‘yi aşmamalıdır. Bypass borusu hiçbir durumda delinmemeli veya direkt olarak kaynaklanmamalıdır. KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 25 3. Kurulum ve çalıştırma Montaj örneği (Manyetik rulo göstergesinde manyetik şalter) ■■ Manyetik şalterdeki sabitleme vidalarını (1) SW 3 mm alyen anahtarı ile yakl. 1 tur gevşetin ■■ Delikli somunu (somunları) (2) manyetik rulo göstergesinin (4) kılavuz somununa (3) yukarıdan ve aşağıdan ittirin (Lütfen kablo vidalamasının veya fişin durumunu şekle göre kontrol edin) ■■ Manyetik şalteri istenilen şalter noktasının seviyesine ittirin ve vidaları sıkıştırarak sabitleyin (Şalter noktası model levhasında belirtilmiştir). Manyetik şalter MA, manyetik rulo göstergesinin (4) sağ tarafına monte edilmek için tasarlanmıştır. Sol tarafa monte edileceği zaman şalter fonksiyonu tersine döner. Şalter ters olarak monte edilmelidir (Model plakası kafanın üstünde bulunur). 26 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D TR Bypass seviye göstergesinin (6) manyetik rulo seviye göstergesindeki manyetik şalterin sabitlemesi delikli somunlarla (şek. 3) gerçekleştirilir. 3.Kurulum ve çalıştırma Şekil 3: Manyetik şalter montajı (Model M, ME, MST, MT) TR Anahtarlama noktası based on 11/2012 GB/D Manyetik şalter montajı (Model MA) KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 27 3. Kurulum ve çalıştırma Montaj örneği (Tutma çubuğundaki manyetik şalter) Manyetik şalterin sabitlemesi, ayrı olarak monte edilmiş bir tutma çubuğu üzerinde gerçekleştirilir (şek. 4). TR ■■ Tutma çubuğunu (1) sabitleme vidalarını (2) gevşeterek ve Bypass seviye sensörünün sabitleme braketinin sö külmesiyle çıkartın. ■■ Manyetik şalteri (4) tutma çubuğuna (1) ittirin ■■ Tutma çubuğunu (1) tekrar Bypass borusuna (5) sabitleme braketleri (3) ve sabitleme vidalarıyla (2) takın ■■ Manyetik şalteri istenilen şalter noktasının seviyesine ittirin ve vidaları (6) sıkıştırarak sabitleyin (Şalter noktası model levhasında belirtilmiştir). Manyetik şalteri istenilen şalter noktasının seviyesine ittirin ve vidaları (6) sıkıştırarak sabitleyin (Şalter noktası model levhasında belirtilmiştir). 28 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D Manyetik şalter montajı (Model MS, MV, MVT, MEx) 4. Bakım 4. Bakım Bypass seviye göstergesi kurallara uygun kullanılması durumunda bakım gerektirmez. Fakat düzenli revizyon çerçevesinde gözle kontrole tabi tutulmalıdır ve kabın basınç kontrolüne dahil edilmelidir. Deneme basıncı model levhasında belirtilen değeri geçmemelidir!) TR Eğer ölçülecek sıvı Bypass seviye göstergesi içerisinde birikebilecek kir parçacıkları içeriyorsa, kullanıcı düzenli aralıklarla destek borusunun temizliğini gerçekleştirmelidir. TEHLİKE! Kaplar üzerinde yapılan çalışmalar sırasında zehirlenme veya boğulma tehlikesi meydana gelebilir. Çalışmalar sadece uygun şahsi koruma önlemleri alınarak (örn. nefes havasını koruma cihazı, koruyucu kıyafet, vs.) gerçekleştirilebilir. Bypass kabı basınç altında olabilir. Bypass kabının içerisinde zehirli, aşındırıcı veya patlayıcı maddelerin bulunması mümkündür. Dışarı sıçrayan sıvı nedeniyle ellerin, kolların, ayakların ve yüzün yanma tehlikesi, ayrıca kızarmalar, zehirlenmeler veya patlamalar nedeniyle yaralanma tehlikesi meydana gelir. Kap açılmadan önce basınçtan arındırılmalıdır. based on 11/2012 GB/D Bypass seviye göstergesinin fonksiyonu sadece orijinal aksesuar ve yedek parçaların kullanılmasıyla garanti edilebilir. KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 29 5. Hata tespiti 5. Hata tespiti Bypass seviye göstergesi kaptaki öngörülen yere monte edilemiyor Bypass seviye göstergesinin Kabın değiştirilmesi dişli boyutu veya flanş boyutu uyuşmuyor Fabrikaya geri gönderme Kaptaki sabitleme bileziğinin dişleri arızalı Bypass seviye göstergesinin vidalama dişi arızalı Kabın merkez mesafesi Bypass seviye göstergesiyle uyuşmuyor Dişlinin tekrar işlenmesi veya sabitleme bileziğinin değiştirilmesi Fabrikaya geri gönderme Kabın değiştirilmesi Fabrikaya geri gönderme İşlem bağlantıları birbirine Kabın değiştirilmesi paralel olarak yerleştirilmemiş Tavsiyelerimiz ve desteğimizle Tavsiyelerimiz ve desteğimizle her zaman yanınızda olmaya çaba gösteriyoruz. Technical alteration rights reserved. Teknik değişiklik hakkı saklıdır. 30 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA based on 11/2012 GB/D TR Aşağıdaki tabloda en sık karşılaşılan hata nedenleri ve uygulanması gereken karşı önlemler belirtilmiştir. Hata Nedeni Tedbir based on 11/2012 GB/D TR KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA 31 KSR KUEBLER Niveau-Messtechnik AG Heinrich-Kuebler-Platz 1 D-69439 Zwingenberg Tel. (+49) 6266 87-0 Faks (+49) 6263 8799 E-postainfo@ksr-kuebler.com Internetwww.ksr-kuebler.com 32 KSR KUEBLER Kullanım kılavuz Bypass-Seviye göstergesi – BNA MM/YYYY country code based on 11/2012 GB/D A division of the WIKA Group