Sıcak Kesim ve Friksiyon Daire Testereler Hot and Friction Circular
Transkript
Sıcak Kesim ve Friksiyon Daire Testereler Hot and Friction Circular
Sıcak Kesim ve Friksiyon Daire Testereler Hot and Friction Circular Saw Blade Diş Formunun Bilenmesi Grinding of the tooth form Sıcak Kesim ve Friksiyon Daire Testereler Hot and Friction Circular Saw Blades Lennartz sıcak kesim ve friksiyon testereleri çekme mukavemeti 8009500 N/mm2 arası özel test edilmiş çeliklerden 2500 mm e çapa kadar üretilmiş testerelerdir. LENNARTZ Hot and Friction Circular Saw Blades with diameters up to 2.500 mm are heavy-duty tools made of tested special steels with tensile strengths between 850 and 950 N/mm2. Sıcak kesim daire testereler sıcaklığı 850° üzeri malzemelerin kesiminde kullanılır. Friksiyon testereler 250° altında sıcaklıkta olan malzemelerin kesiminde kullanılır. Hot and Friction Circular Saw Blades are used for cutting slabs, billets, plates, tubes and profiles. Hot Circular Saw Blades are used with cutting material temperatures > 850° C. Friction Circular Saw Blades are, in contrast, used with cutting material temperatures < 250° C. İki kesim metodu da eritip-kesme ilkesine dayanır. Kesim alanında üretilen sürtünme ısısı kesim alanı sıcaklığını neredeyse malzemeyi sıvılaştıracak sıcaklığa yükseltir.Bu 140 metre/saniye kesim hızını gerektirir. Malzemenin kalitesine göre 80-200 mm/dakika arası bir ilerleme değeri gerekir. . Both sawing methods are based on fusion-cutting. Frictional heat produced in the cutting area leads to temperatures that come close to the liquefaction limit. This requires a cutting speed Vc = 100 – 140 m/sec. The saw tooth sector requires an adequate pressurised water cooling process in order to flush out debris from the tooth gullet. A feed rate of Vf = 80 – 2.000 mm/min is achieved, depending on the material being cut. 3 Diş Sertleştirme Inductive tooth hardening 4 Dizaynlar Designs D= Testere Çapı (mm) Diameter of saw blade (mm) ap= Kesme Genişliği (mm) Cutting width (mm) B= Göbek Çapı (mm) Diameter of centre bore (mm) C= Flanş Çapı(mm) Diameter of flange (mm) Dizayn 1: Siyah Haddelenmiş Design 1: Black rolled Dizayn 2: Taşlanmış Yüzey Design 2: Face ground Dizayn 3: Konik Zemin Design 3: Taper ground Yaygın Diş Geometrileri Common Tooth Geometries γ0 α0 γ0 α0 α0 Pendulum Diş Pendulum tooth γ0 /α0 = 30° γ0 /α0 = 30° Profiller boru ve dolu malzemelerin sıcak kesimi için uygundur Özel Dizayn Sertleştirilmiş Diş Ucu Special design with Papağan Diş Parrot tooth hardened tooth tip γ0 = 0° α0 = 8° γ0 = 0° α0 = 8° Boru ve profillerin soğuk kesimi için uygundur suited for hot and cold cutting of tubes, profiles, beams and suited for cold cutting of tubes, profiles and beams. solid materials. Özel Diş Geometrisi Special Tooth Geometry Elmas Uçlu Çelik boru ve profilleri sıcak kesiminde kullanılır Avantajları: • Klasik testerelere göre 10 kata kadar arttırılmış testere ömrü • Ekonomik Kesim • Az Çapak Carbide tipped Used for hot sawing: tubes and profiles, steel cutting Advantages: • Increase of tool life up to factor 10 as compared with traditional systems • Economical cutting • Less burrs T = Hadve (mm)/Tooth pitch (mm) α0 = Temizleme Açısı /Clearance angle γ0 = Kesme Açısı /Rake angle Kesme Genişliği (mm)/Cutting width ap = (mm) 5 Diş Formunun Firezelenmesi Milling of the tooth form 6 LENNARTZ ECOcut LENNARTZ ECOcut WM 70 CrV Steel 1.2604 1.2235 LENNARTZ Co, Almanya, müşterilerin kesebilecek testere talepleri doğrultusunda özel firiksiyon daire testeresi “LENNARTZ ECOcut” geliştirdi. • Yuvarlak Borular • Round tubes/pipes • Kare ve Dikdörtgen Borular • Square and rectangular tubes .Lennartz ECOcut tamamen sertleştirilmiş özel çelikten üretilmiştir. Bu diş formu özellikle kaynaklı boru ve profillerin kesimi için geliştirilmiştir. • • • • • Profiller • Profiles LENNARTZ ECOcut is made of evenly and fully hardened special steel. The surface is thermo-chemically refined. The tooth geometry is specifically developed to saw welded tubes and pipes. %250 uzun testere ömrü Çatlak oluşmasını önler Daha az çapak Bilenebilir Außendurchmesser LENNARTZ Co., Germany developed the special Friction Circular Saw Blade “LENNARTZ ECOcut” because of customers’ particular demands for a blade that can saw • • • • outside diameter A Up to 250% longer blade life Reduction of cracking Less burrs Can be re-sharpened Firiksiyon daire testerelere göre Lennartz ECO Cut firiksiyon daire testere sizlere daha ekonomik ve verimli boru ve profil kesimini sağlar. LENNARTZ ECOcut çap 300’den 1800 mm’e kadar üretilir. Tavsiye edilen kesme hızı 120- 140 m/sn ‘dir. LENNARTZ Nebenlochdurchmesser Haupt- bohrung pin center bore hole diameter Compared to all other available Friction Circular Saw Blades, the LENNARTZ ECOcut Friction Circular Saw Blade allows you to saw pipes and tubes more efficiently and economically. Made in Germany The LENNARZT ECOcut Friction Circular Saw Blade is available in dimensions with diameters between 300 mm and 1.800 mm. Recommended cutting speed: 120 – 140 m/sec Diş Geometrisi Tooth Geometry Papağan Diş Parrot tooth Pendulum Diş Pendulum tooth LENNARTZ ECOcut